Difference between revisions of "OLED - Organic Light Emitting Diode"

Revision as of 02:32, 16 February 2011

Introduction

The growing number of electronic devices using organic light emitting diode displays shows that after years of promise, the technology is increasingly finding place in many products. But while OLED displays might challenge LCDs as the screens of choice for smaller gadgets, the technology may not become mainstream for notebook PCs or TVs within this decade.

OLED displays use organic compounds that emit light when exposed to an electric current. They are brighter, have better contrast, offer wider viewing angles, use less power, and provide faster response times than liquid crystal displays. OLED screens' thickness is a third of that of LCDs, since they don't need a back-light, and that makes them a good fit for portable electronics devices.

OLED Components

An OLED consists of the following parts:

• Substrate (clear plastic, glass, foil) - The substrate supports the OLED.
• Anode (transparent) - The anode removes electrons (adds electron "holes") when a current flows through the device.
• Organic layers - These layers are made of organic molecules or polymers.
  • Conducting layer - This layer is made of organic plastic molecules that transport "holes" from the anode. One conducting polymer used in OLEDs is polyaniline.
  • Emissive layer - This layer is made of organic plastic molecules (different ones from the conducting layer) that transport electrons from the cathode; this is where light is made. One polymer used in the emissive layer is polyfluorene.
• Cathode (may or may not be transparent depending on the type of OLED) - The cathode injects electrons when a current flows through the device.

Working of OLED'S

• OLEDs emit light in a similar manner to LEDs, through a process called electrophosphorescence.
• The process is as follows:

1. The battery or power supply of the device containing the OLED applies a voltage across the OLED.
2. An electrical current flows from the cathode to the anode through the organic layers (an electrical current is a flow of electrons).

• 1. The cathode gives electrons to the emissive layer of organic molecules.
• The anode removes electrons from the conductive layer of organic molecules. (This is the equivalent to giving electron holes to the conductive layer.)

1. At the boundary between the emissive and the conductive layers, electrons find electron holes.

• When an electron finds an electron hole, the electron fills the hole (it falls into an energy level of the atom that's missing an electron).
• When this happens, the electron gives up energy in the form of a photon of light (see How Light Works).

1. The OLED emits light.
2. The color of the light depends on the type of organic molecule in the emissive layer. Manufacturers place several types of organic films on the same OLED to make color displays.
3. The intensity or brightness of the light depends on the amount of electrical current applied: the more current, the brighter the light.

OLED Types

There are several types of OLEDs

• Passive-matrix OLED
• Active-matrix OLED
• Transparent OLED
• Top-emitting OLED
• Bottom-emitting OLED
• Foldable OLED
• White OLED

Passive-matrix OLED - PMOLED

PMOLEDs have strips of cathode, organic layers and strips of anode. The anode strips are arranged perpendicular to the cathode strips. The intersections of the cathode and anode make up the pixels where light is emitted. External circuitry applies current to selected strips of anode and cathode, determining which pixels get turned on and which pixels remain off. Again, the brightness of each pixel is proportional to the amount of applied current.

PMOLEDs are easy to make, but they consume more power than other types of OLED, mainly due to the power needed for the external circuitry. PMOLEDs are most efficient for text and icons and are best suited for small screens (2- to 3-inch diagonal) such as those you find in cell phones, PDAs and MP3 players. Even with the external circuitry, passive-matrix OLEDs consume less battery power than the LCDs that are currently used in these devices.

Active-matrix OLED - AMOLED

AMOLEDs have full layers of cathode, organic molecules and anode, but the anode layer overlays a thin film transistor (TFT) array that forms a matrix. The TFT array itself is the circuitry that determines which pixels get turned on to form an image.

AMOLEDs consume less power than PMOLEDs because the TFT array requires less power than external circuitry, so they are efficient for large displays. AMOLEDs also have faster refresh rates suitable for video. The best uses for AMOLEDs are computer monitors, large screen TVs and electronic signs or billboards.

Transparent OLED

Transparent OLEDs have only transparent components (substrate, cathode and anode) and, when turned off, are up to 85 percent as transparent as their substrate. When a transparent OLED display is turned on, it allows light to pass in both directions. A transparent OLED display can be either active- or passive-matrix. This technology can be used for heads-up displays.

Top-emitting OLED

Top-emitting OLEDs have a substrate that is either opaque or reflective. They are best suited to active-matrix design. Manufacturers may use top-emitting OLED displays in smart cards.

Foldable OLED

Foldable OLEDs have substrates made of very flexible metallic foils or plastics. Foldable OLEDs are very lightweight and durable. Their use in devices such as cell phones and PDAs can reduce breakage, a major cause for return or repair. Potentially, foldable OLED displays can be sewn into fabrics for "smart" clothing, such as outdoor survival clothing with an integrated computer chip, cell phone, GPS receiver and OLED display sewn into it.

White OLED

A white organic LED (OLED) incorporating a blue phosphorescent dye and a down-conversion phosphor has achieved a luminous efficacy of 25 lm/W. This high-efficacy device was enabled by lowering the device operating voltage, increasing the outcoupling efficiency, and incorporating highly efficient phosphorescent emitters.

Landscape Analysis Of Top-Emmission OLED

IP Landscape

• We have chosen the top emission OLED's as the area of focus.
• The top emission OLED's have been facing challenges to achieve optimimum efficiencies in terms of light reflection. Also, it's been a challenge to increase the life time of the top emission OLED's. Lots of initiative is seen in this direction, and below is a snapshot of research work done by organizations worldwide to achieve higher efficiency levels through better design.

Like this report?

This is only a sample report with brief analysis
Dolcera can provide a comprehensive report customized to your needs

Competitor Landscape

Competitor Mapping

Key Inventors

Key Inventor Mapping

Technology Mapping

• In OLED devices not all internally generated light is coupled out of the device (only 20%-50%), which reduces the device efficiency and lifetime.
• Modification in structures are applied to improve outcouple efficiency in order to enhance the efficiency and lifetime of top emission OLEDs.
• Below is a snapshot of how various organizations are using different design structures, using the same principle of internal reflection, to achieve higher out-coupling efficiencies.

Comparison of out coupling of waveguiding light in top-emission polyLED stack

• Some light is reflected out of the OLED at stray angles in typical cases. By using a barrier material (form of microparticles) in the cathode layer, this light at stray angles hits the barrier material, and some of it is reflected back and guided out at the right angles, reducing light loss.

• Microparticles are incorporated in the substrate, which prevents light loss by reflecting light emitted at stray angles.

• A highly reflective anode is provided made of Aluminium or Silver, with a mirror like finish, to reflect light.

• A shielding layer is provided below the anode, across its entire surface, thus increasing the surface area from which light can be reflected outside.

• The reflective layer, anode, is made of a highly reflective surface like Aluminium alloy or silver.

Conclusion

The innovation is towards:

• Incorporating micro-particles structure over the substrate that provide a reflective surface.
• Highly reflective materials using metals like Molybdenum etc.

Like this report?

This is only a sample report with brief analysis
Dolcera can provide a comprehensive report customized to your needs

Contact Dolcera